11/6/2023 0 Comments Pallet of cinder blocksNow, The bar is pretty darn awesome, I have to say. I’m hoping to do a full video update on the bar soon, and will embed it here when it’s done. And I was concerned about kids running into them. I’ll admit it’s not the prettiest solution. He bought a set of clamps, and clamped the bar to each of the concrete pillar legs. So, my husband came up with an interesting, easy, and inexpensive alternative: clamps. ![]() We considered using construction adhesive, but were still concerned that it would degrade over time. I wanted to use sleeve anchors, which are made to go into masonry, but we couldn’t figure out exactly how to get the drill bits into the tight space that was allotted by the pallet. Again, you can use glue to hold this in place if you like.Īttaching the Pallet to the Cinder BlocksĪlthough the weight of the finished pallet should make it pretty secure, there is still a risk of the bar tipping from guests leaning on it.Ģ018 Update! How we resolved holding the pallet in place.Īt the time I originally shared this post, the Husband and I couldn’t agree how to actually attach the pallet to the cinder blocks. Finally, add a 1-inch furring strip of wood between the post and the cinder blocks to hide the outside edges of the corrugated sheet metal.The should be long enough to be held in place with pressure, but, you can add some wood glue if it makes you feel more comfortable. Stain and seal three 1×4 boards cut to fit between each post.(I started each hole by hammering a screw in the spot that needed the hole.) Don’t forget to wear ear muffs to protect your ears. Attach the corrugated sheet metal to the back of the posts using exterior screws.(In our case, that was about 24 inches between posts). Placing the corrugated sheet metal against the cinder blocks and then install the 4×4 posts evenly along the front of the sheet metal.Cut four 4×4″ exterior posts approximately 36 inches long.And always be sure to wear protective gear, no matter how you’re cutting metal. If you have the right power tools, definitely use them here. I used tin snips, which was not easy, and left sharp edges. Carefully cut corrugated sheet metal to the length of your table.(FYI, Paver base, sand, or pea gravel would have worked better) So here’s what we did: I found 1×4 boards in our garage to act as ‘skids” with marble rock underneath them in the low areas. Our ground just couldn’t seem to level off, no matter how much we tamped.Lay down landscaping fabric to help prevent weeds.You can either rent a tamper, or use a hand tamper as we did. Do your best to level an area wider than your pallet.Screw in each board to the gaps in the pallet using exterior-grade screws.Don’t forget to add a water sealant to these as well. Sand down the plywood to remove any rough edges and stain the plywood and the pallet.(I had the hardware store do this for me) Cut 1/2-inch plywood according to the measurements noted.Make sure to measure the width of each gap at several points, to ensure they are fairly even. Carefully measure and note any gaps between the boards in your pallet.Optional: Sleeve Anchors and/or Construction Adhesive.8-foot sheet of corrugated steel roofing.4, 4 x 4 wood posts, cut to 36″ lengths.Patio Base/Pea Gravel/Sand (I used marble rock).3 1×4 boards cut to the width of the bar.4 x 4 x 1/2 plywood, cut into appropriate lengths by the hardware store.DIY Outdoor Bar with Cinder Blocks and a Pallet: Materials: That’s just what I was dealing with after the rain we’ve had. I’ll apologize now for the muddy build pictures. By the time he came home, it was completely finished. Seriously, as the husband sat in meetings, I texted him pictures of my progress. The most time-consuming parts were actually the preparation of the pallet (filling in the gaps) and leveling the ground underneath. I won’t lie, this gigantic outdoor bar was a lot of work.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |